October 22, 2021

Why My Car Wipers Not Working (9 Tips)

How often have you been caught in the middle of a rainstorm, only to find out that your car’s wipers are not correctly adjusted? 

Your wipers are one of the most essential parts of your car, and without them functioning, it will be dangerous driving in a storm. 

But did you know that up to a third of all wiper blade can problems be traced back to a poor installation? 

These simple measures will ensure that your wiper blades are in good working properly.

When was the last time you checked your wiper blades, or maybe ask yourself why wiper blades do not work at all? 

Car wipers are one of those simple but frustrating things. Suppose there is no visibility on the road when you drive.

 In that case, it will affect your driving safety severely with malfunction wiper blades.

Why My Car Wiper Blades Does Not Work? 

Many people might think if their car windshield wipers do not operate, as usual, they need to replace them right away. 

However, this problem might be another reason: most

likely an incorrect installation of the new wiper blades. 

Even a single small mistake in installing your windshield

wipers may cause them to streak, chatter, and leave

annoying streaks behind. 

If wipers do not wipe properly, they will not become

sufficiently clear rain or snow off your windshield. 

With an incomplete clean, vision becomes impaired, and

the drive becomes dangerous and uncomfortable. Wipers

that chatter can be a safety hazard.

What to Do When Car Wiper Blades Do Not Work? 

If you have recently replaced wiper blades, you must check them for proper operation after installing them on your vehicle. 

Check if the motor runs without any problems when turning the switch to high speed and low speeds. 

Be sure to examine any obstructions between the wiper’s

metal arm or blade and the glass surface, such as ice or

insects, before driving your car in bad weather conditions.

Are There Any Special Tips for Installing Windshield Wiper Blades? 

When installing the new wipers, it is very important to install them according to the manufacturer’s instructions. 

Make sure they fit perfectly to your car model and on your windshield. 

Improper installation may cause the wipers not to work as expected. 

For example, suppose a part of the rubber blade doesn’t

touch the surface because it’s incorrectly placed or misaligned. 

You can have difficulties getting even wiping motions from one side of the glass to the other in that case.

If you are sure that nothing is wrong with your wiper

blades and motor but still have a problem with proper

usage of your wiper blades, you should check something else in your car. 

Check for any obstructions such as ice, dirt, or bugs, and remove them immediately when you notice them. 

Remember to check the washer reservoir and make sure it is full of fluid and not empty.

How to Remove Ice from Windshield Wipers? 

Ice also can stop the wiper blade from working correctly,

so removing it before driving will do a great favor to you

in case of difficult visibility.

 You just need to use another pair of warmed-up wipers

instead of cold ones from frozen blades, then perform

wiping motion four times on both left and right sides until ice starts melting away.

What Happens to wiper Blades when It is Too Hot outside?

Too much hot weather can cause your wiper blades to dry out and shrink. 

Even it’s only a bit too warm, this will be an issue for the

rubber or squeegee material in the blade that holds all the

water you need for wiping. 

In such a case, no matter how hard you try using your

wipers, it won’t work because there will not be enough

water on your windshield. 

As a result, you may see streaks on your window and experience annoying noises that make driving unsafe.

If this is so, you should change them as soon as possible before they become damaged or worn out completely.

 And now another tip – never use a high-pressure spray 

the nozzle on your windshield. 

The force of water under pressure can damage the rubber blades and cause them to crack or break.

How to Store Windshield Wiper Blades? 

If you’re going to keep your wipers for more than two weeks, make sure they’re kept dry and at room temperature.

 Never expose wiper blades to heat because it will make
the rubber deteriorate quickly, reduce adhesion, and gum up with dirt and grease.

 Avoid keeping them in direct sunlight; UV exposure will

also severely affect their softness and flexibility.

If you intend to keep them for an extended period, apply

a thin coat of silicone fluid or mineral oil to the metal part before storing it.

You can easily clean your wiper blades by spraying some

windshield washer fluid or soap water and wiping it off with old newspapers.

How to Install Tear Drop Wipers? 

The best way to install the teardrop wipers is to ensure

that they are installed according to their own manufacturer’s instructions. 

If not, it will create a problem when your car is running on 

the road and you may experience difficulty seeing clearly from them.

 And always remember that correct installation will

prevent any difficulties in using these wipers properly; do not forget to read carefully about it.

What Happens When You Use Old Wiper Blades? 

When you use old wiper blades, it is obvious that they will show signs of wear and tear even if you use them every day.

When you replace your windshield wipers, do so immediately because they could have accumulated dirt and ice that will obstruct the vision on other drivers’ side.

9 Tips Why Your wipers Not Working

 Check the glasses: 

If they have any chips or cracks, it’s time for new ones!

Glasses chipped or cracked will simply transfer dirt from one side of the window to the other.

Check the rubber: Most wipers have a rubber strip that attaches the blade to the wiper arm. 

This strip can become loose or even rot, so make sure it’s in good shape.

Check your motor: 

If your blade doesn’t move, check to be sure your wiper motor is connected correctly. 

Sometimes they slip out of place and need to be adjusted.

Also, make sure there isn’t any lint or other debris clogging up the works.

 Check your wiper blades

When you turn on the wipers, are they wiping properly? 

If not, it’s likely that your blades are worn out and need replacing. 

A worn-out blade will not wipe cleanly and causes streaks and smears on your windows. 

Check your washer fluid level: 

If there is plenty of washer fluid, the wipers will clean your windshield better.

Check your wiper arms: 

Do they move up and down easily? 

If not, you may need to change them or lubricate them.

Mechanical Failures: 

If you have followed all of these steps and your wipers still don’t work, you may have a mechanical failure. 

Bring your vehicle to a professional for a complete check-up.

Weather Conditions: 

Cold weather can cause your windshield wipers to streak, while rain or snow can decrease your visibility.

Wrong Settings

Make sure your wipers are set to clear, not just wipe. This will help eliminate streaks and smudges.

Winter Maintenance: 

If your blades have been exposed to salt or corrosives from the winter road de-icers, they may need replacing.

Poor Quality Wiper Blades: 

Time for new blades if yours have been in place for several years. 

Blades made of inferior materials tend to wear out faster than those made of quality materials.

Higher-quality wiper blades also fit more snugly on the arms, which can eliminate noise and vibrations.

Wrong wipers for your car: 

If you happen to have a custom car, make sure the windshield wipers you use are made for your vehicle. 

Don’t assume that the wiper blades you have come with your kit will fit your car. 

Contact a professional or head to our website and perform a quick search on your vehicle.

Wiper Blades: 

Are they the right type for your windshield? 

Do they clean properly?

 If not, get new ones. There are different types of wipers

available — like those with rubber blades or those that

spray water — so make sure you choose the correct ones for your car. 

How Does My Windshield Wiper Work?

Most of us take our windshield wipers for granted, and we

like to believe that they work all the time. 

But that isn’t always the case. You should know how your

windshield wiper works and when you need to replace it.

The mechanism behind it is very simple and easy to understand.

How Can I Install My Wipers? 

If you have never installed wipers, it isn’t too hard to do yourself.

Set the wiper switch to the high setting if you want your

wipers to wipe more aggressively. 

The more they wipe, the less streaking will occur.

You can also set the switch to the intermittent setting. 

This will have your wipers wipe every time you turn on your vehicle.

Wiping your windshield is a great way to clear off the

moisture and dirt in front of you. It’s also one of the first steps an auto technician will take when servicing a vehicle. Your car’s wiper blades should be changed out regularly so that they are working as effectively as possible.

How Much Does Car Wipers Cost For An Suv Or Car? 

Wiper blade prices range from $7 to $40, depending on

the type of wiper blade you require. 

The first thing that you will have to do is determine what

type of wiper blades are needed. 

Wiper blades for cars come in various styles, with some

being better than others depending on the climate and season.

How To Change a Windshield Wiper Blade?

The process is pretty simple. You will need a few tools like

a screwdriver, wrench, torch lighter or butane lighter, and

possibly a pair of pliers or vise grips.

If you want to change your wiper blades, do not forget to

check their size and shape first. 

You will need a pair of pliers, safety glasses, gloves, and a

flat head screwdriver to perform this task. 

Step 1: 

To remove old blades from the windshield, start by

removing any visible components holding them into

places, such as clips or springs. 

Then use a flathead screwdriver quickly loosen the end

caps that are usually secured around the base of the blade

arms before pulling off these components with pliers. 

The old metal parts may be bent out of shape because

they were attached tightly but try your best not to bend

them more than necessary to avoid damaging their structure. 

Step 2: 

Unhook the linkages from both ends of the wiper arms and separate them away from the windshield wipers assembly. 

Once again, bend only the metal parts as necessary so that they can be moved out of your way.

 Step 3: 

Clean each end with a clean cloth to remove dirt or grime if any is found there. 

If possible, use a solvent such as lacquer thinner to clean off any adhesive left on old blades before removing them completely.

Step 4 – 

Carefully pull out the new blade set by pulling it straight

down when all components are correctly removed, then fit one side onto each arm.

 Secure it tight by releasing tabs on each end of the arm until you hear a click sound. 

Ensure that the wiper blades are correctly attached to the arms, or else they will not work effectively.

 Step 5: 

Before you start using your new wiper blades, ensure that

you test them for at least a few minutes over the dry glass without any washer fluid.

(so that it can get used to working conditions before putting under pressure)

Step 6: 

Never worry about streaks and marks that are left on your windshield because of new wiper blades. 

Cleaning the window just doesn’t work sometimes.

If you find that some greasy residue has been building up

after a long time, wiping it off with water or glass cleaner simply won’t do the trick.

The best way to get rid of those horrid streaked lines is by

loosening them from under your nose in two swift motions: one side at a time.

Just use a pencil eraser and rub over the rubber part

gently to remove those stubborn streaks quickly and

cleanly without leaving behind any trace of dirt.

By following these simple tips, you should keep your

wipers in good shape throughout the winter season. 

If they’re not working, now’s the time to replace them while they’re not being used. 

Doing it yourself is simple with our detailed online install videos. 

 Good luck on changing your wiper blades, and always

remember to read the instructions carefully before using

them to avoid any problem with it.

Sources
 firestonecompleteautocare.com

Images by the blowup@theblowup